StampP4X

Support the following products:

StampP4X

UiFlow2 Example

ADC Input

Open the stampp4x_adc_example.m5f2 project in UiFlow2.

https://static-cdn.m5stack.com/mpy_docs/controllers/stampp4x/stamp4x_adc_example.png

This example reads the 16-bit ADC value from GPIO23 every 200 ms and prints the result to the serial console.

GPIO Output

Open the stampp4x_gpio_example.m5f2 project in UiFlow2.

https://static-cdn.m5stack.com/mpy_docs/controllers/stampp4x/stamp4x_gpio_example.png

This example toggles GPIO15 high and low once per second and prints the current output state to the serial console.

PWM Output

Open the stampp4x_pwm_example.m5f2 project in UiFlow2.

https://static-cdn.m5stack.com/mpy_docs/controllers/stampp4x/stamp4x_pwm_example.png

This example outputs a 20 kHz PWM signal on GPIO15. The duty value repeatedly ramps between 0 and 1023 and is printed to the serial console.

MicroPython Example

ADC Input

This example reads the 16-bit ADC value from GPIO23 every 200 ms and prints the result to the serial console.

 1import os, sys, io
 2import M5
 3from M5 import *
 4from hardware import ADC
 5from hardware import Pin
 6import time
 7
 8
 9adc23 = None
10
11
12last_time = None
13
14
15def setup():
16    global adc23, last_time
17
18    M5.begin()
19    adc23 = ADC(Pin(23), atten=ADC.ATTN_11DB)
20    last_time = time.ticks_ms()
21
22
23def loop():
24    global adc23, last_time
25    M5.update()
26    if (time.ticks_diff((time.ticks_ms()), last_time)) >= 200:
27        last_time = time.ticks_ms()
28        print((str("ADC(pin23): ") + str((adc23.read_u16()))))
29
30
31if __name__ == "__main__":
32    try:
33        setup()
34        while True:
35            loop()
36    except (Exception, KeyboardInterrupt) as e:
37        try:
38            from utility import print_error_msg
39
40            print_error_msg(e)
41        except ImportError:
42            print("please update to latest firmware")

GPIO Output

This example toggles GPIO15 high and low once per second and prints the current output state to the serial console.

 1import os, sys, io
 2import M5
 3from M5 import *
 4from hardware import Pin
 5import time
 6
 7
 8pin15 = None
 9
10
11last_time = None
12enable = None
13
14
15def setup():
16    global pin15, last_time, enable
17
18    M5.begin()
19    pin15 = Pin(15, mode=Pin.OUT)
20    last_time = time.ticks_ms()
21
22
23def loop():
24    global pin15, last_time, enable
25    M5.update()
26    if (time.ticks_diff((time.ticks_ms()), last_time)) >= 1000:
27        last_time = time.ticks_ms()
28        enable = not enable
29        if enable:
30            print("set pin15 high")
31            pin15.on()
32        else:
33            print("set pin15 low")
34            pin15.off()
35
36
37if __name__ == "__main__":
38    try:
39        setup()
40        while True:
41            loop()
42    except (Exception, KeyboardInterrupt) as e:
43        try:
44            from utility import print_error_msg
45
46            print_error_msg(e)
47        except ImportError:
48            print("please update to latest firmware")

PWM Output

This example outputs a 20 kHz PWM signal on GPIO15. The duty value repeatedly ramps between 0 and 1023 and is printed to the serial console.

 1import os, sys, io
 2import M5
 3from M5 import *
 4from hardware import PWM
 5from hardware import Pin
 6import time
 7
 8
 9pwm15 = None
10
11
12duty = None
13last_time = None
14dir2 = None
15
16
17def setup():
18    global pwm15, duty, last_time, dir2
19
20    M5.begin()
21    pwm15 = PWM(Pin(15), freq=20000, duty=512)
22    duty = 0
23    dir2 = True
24    last_time = time.ticks_ms()
25
26
27def loop():
28    global pwm15, duty, last_time, dir2
29    M5.update()
30    if (time.ticks_diff((time.ticks_ms()), last_time)) >= 10:
31        last_time = time.ticks_ms()
32        duty = (duty if isinstance(duty, (int, float)) else 0) + 1
33        if duty >= 1023:
34            duty = 0
35            dir2 = not dir2
36        if dir2:
37            pwm15.duty(duty)
38            print((str("duty: ") + str(duty)))
39        else:
40            pwm15.duty((1023 - duty))
41            print((str("duty: ") + str((1023 - duty))))
42
43
44if __name__ == "__main__":
45    try:
46        setup()
47        while True:
48            loop()
49    except (Exception, KeyboardInterrupt) as e:
50        try:
51            from utility import print_error_msg
52
53            print_error_msg(e)
54        except ImportError:
55            print("please update to latest firmware")